search

Audiovox DVD-220 Guide d'installation Page 38

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 47
  • Table des matières
  • DEPANNAGE
    •
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 37
TRIM RING INSTALLATION:
Note: This page only covers special installation considerations for thick trim ring installation.
If
the video monitor is to be installed
in
a vehicle with the thick trim ring, it may need to be
trimmed
to
fit the contour
of
the vehicle head liner.
Note:The trim rings supplied with this unit are not designed
to
be trimmed.
1)
In
this installation, the video monitor is mounted directly to the overhead cross-member
in
the roof using the mounting screw bosses. These screw bosses should contact the cross-
member directly (i.e.:
no
gap between the screw boss and the roof structure). Also, be sure
that the screws do not pierce the outer roof skin when fully fastened
to
the cross-member.
The trim ring is attached to the video monitor using the perimeter screw bosses. It is
important that the screws used
in
this installation are not over tightened, and that the video
monitor and trim ring are mounted
in
such a way that the assembly does not distort (or
bend) when the mounting screws are tightened. An alternate method is to use the
mounting bracket. First secure the mounting bracket to the cross-member, then screw the
monitor into the mounting bracket. See the drawing
in
this manual.
2)
It is best to mount the video monitor
to
the roof structure without the trim ring first. There
should
be
a gap between the headliner and the outer flange of the video monitor. The
trimring should be cut to fill this gap. Apply masking tape
to
the outer surface
of
the trim
ring
in
the areas where the cut will
be
made.
3)
Mark the cut to follow the necessary contour of the roof. The suggested method
of
marking
is as follows:
A) First mark the narrowest point of the trim ring
on
the masking tape.
Be
careful to
consider not only vertical location, but fore-aft location.
B)
Using the handle of a screwdriver, make a "transfer marking tool". See diagram below.
Place the tool against the roof and the marker against the masking tape
on
the trim
ring. Trace the cut to
be
made around the entire perimeter
of
the trim ring.
C) Cut the trim ring using a sharp utility knife or shears. Make the cut
in
several passes
over the marked line, each time cutting a little deeper. It is not necessary to cut
completely through the plastic, the cut only need be over 50% of the wall thickness
of
the plastic. By bending the cut back and forth several times, the plastic will break
cleanly at the cut.
D) Check the fit of the trimmed console and make any minor adjustments necessary.
4) The trim ring can be painted or covered with a material that matches the head liner before
assembling the trim ring to video monitor.
5)
The finished trim ring should be attached to the video monitor, then attach the assembly to
the roof.
~
Tape
marker
to
screwdriver.
Starting at your mark for the
lowest point, trace the contour
of
the roof
7
Vue de la page 37
1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 46 47

Commentaires sur ces manuels

Pas de commentaire
  • Andersen Sterilizers CoolIT Pacific-cycles EDGE Tech Woodsman
  • Rolls Composants des dispositifs de sécurité Genicom Imprimer et scanner Avanti Micro-ondes Panasonic Les téléviseurs à plasma Coway Non
  • Char-Broil Red 463250110 RocketFish RF-RBKIT Jvc EX-A5
  • Pocketbook SURFpad 4 M Manuel de l'utilisateur VIORE LED32VH30 Guide d'installation Prology DNU-2610 Manuel de l'utilisateur D-Link DES-1228P - Web Smart Switch Manuel de l'utilisateur Samsung GT-E1260B Manuel de l'utilisateur