Audiovox PRO 9232 Manuel d'utilisateur télécharger pdf

KEYLESS ENTRY ALARM UPGRADE MODULE

PRE - INSTALLATION NOTES :

This system provides an output that is used to drive the siren, and an output that can pulse the vehicle's horn. When

utilizing the horn, an additional relay maybe required. Caution: on many vehicles the factory horn is not

designed for continuous use, and it is recommended that the siren is used for these vehicles. Check to see

if the horn in the vehicle is the same part that is used in a vehicle with the factory installed security system.

STAND ALONE PASSIVE ALARM

When installing the PRO-9232 as a stand alone passive alarm system, the following programmable features must

be set:

Feature #5 set to Passive.

Feature #7 set to Delay.

Feature #8 set to 1 Wire Disarm.

IMPORTANT

: In the entry delay mode, when the alarm is armed actively, the doors will trigger the alarm

instantly. The entry delay will only take place when the alarm is allowed to arm passively!

IMPORTANT

: THE ENTRY DELAY WILL NOT OPERATE WHEN THE VOLTAGE SENSING CIRCUIT,

FEATURE # 6, IS ACTIVE

AUXILIARY FUNCTION or REMOTE START OUTPUT

This system includes an additional transistorized ground output that can be used to trigger an external remote starter

or remote window closure module. This is the Green w/Black trace wire, and it is activated by pressing the Lock,

then Unlock, then Lock buttons on the factory transmitter within a 3 second time period.

REMOTE PANIC

This system will allow the activation of remote panic using the factory transmitter. Pressing the Unlock, the Lock,

then Unlock buttons on the factory transmitter within a 3 second time period will activate the remote panic feature.

TRUNK TRIGGER BY - PASS INPUT

This system provides a positive trunk release input, which allows the activation of the remote trunk release from

the OEM transmitter without triggering the alarm, even when the system is armed.

VALET / MANUAL OVERRIDE SWITCH

This system provides a valet/manual override switch which is operable by use of a custom code override or only

after the system is disarmed. There is no need to conceal this switch as the override code is known only to the

operator.

UNDERSTANDING DISARM #1 AND #2:

Because of the complexities of the different factory installed Remote Keyless Entry Units on the market today, the

PRO- 9232 uses two disarm inputs. Whether installing into a vehicle using a 2-step unlock circuit, single step unlock

circuit, or as a stand alone passive alarm, both disarm wires must be connected in all installations.

The arm and disarm functions of this system are learned during power up, by monitoring the resting state of the

factory wires when power is applied to the unit. Be certain all wires are connected to the vehicle before applying

power to the circuit to insure the system responds only during operation from the factory transmitters.

NOTE: By design, if feature #8 is set to the "ON" position, (1 wire disarm), the alarm will not disarm while the

system is in the triggered mode.

Model PRO 9232

INSTALLATION INSTRUCTIONS

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Model PRO 9232

KEYLESS ENTRY ALARM UPGRADE MODULEPRE - INSTALLATION NOTES :This system provides an output that is used to drive the siren, and an output that can pu

Page 2

INSTALLATION OF MAJOR COMPONENTS :ALARM CONTROL MODULESelect a mounting location inside the passenger compartment ( up behind the dash ), and secure i

Page 3 - IMPORTANT!

It is recommended that when installing this system into vehicles with electronic “ after fans, “ the procedure for hardwireshould be followed.HARDWIR

Page 4 - Door Lock Control Circuits

LIGHT GREEN WIRE : (-) INSTANT TRIGGER ZONE 1This is an instant activation ground trigger wire. This wire should be reserved for connection to option

Page 5

RED w/BLACK TRACE WIRE : DISARM INPUT #2Connect this wire to the unlock side of the door lock/unlock switch or any passenger door unlock motor wire, w

Page 6

The factory default settings for the selectable features are:Feature #1 = 1 Chirp, 1 Flash, 800ms door lock, 800ms door unlock.Feature #2 = 2 Chirps

Page 7

Delay Select.Siren/Horn Chirp 7x, Light Flash 7x, LED Flashes 7x Pause, 7x Pause, indicating feature 7 selected. Use Factory Lockbutton of transmitte

Page 8